You have no items to compare.
Starting at: $0.00
C – Loctite 648
E – Loctite Anti-Seize 15378
a – Marked with S/N;
b – Stainless;
c – In a roll, Tube 125 mm (4.92 in.);
d – With imprinting "oil";
e – See Service Instruction SI-914-022 current issue;
f – With additional internal bracket from engine S/N 914F 4,420.437;
g – With lubricaiton hole for waste gate shaft
Starting at: $0.00
B – Loctite 243
a – Marked with S/N;
b – Only for TCU P/N 966470;
c – For cylinder 2/4;
d – For cylinder 1/3;
e – Used as water trap;
f – Also included in carburetor for 914 Cyl. 2/4;
g – Drip tray for airbox P/N 867758, 667162 and 667167;
h – For use of airbox P/N 667162. See SI-914-013 current issue;
i – For use of airbox P/N 667167, See SI-914-015 current issue;
j – For use of airbox P/N 867753;
k – New adapter flange use only together with throttle valve position sensor. See SI-25-1997;
l – See Service Instruction SI-914-022 current issue;
m – Optional for fuel pressure gauge connection;
n – Not for TCU P/N 966470
Starting at: $0.00
B – Loctite 243
C - Loctite 648
L – Klueber Isoflex Topas Nb5051
O – Engine Oil
a - Thread 3/4-16 UNF for oil filter 3 mm extended, Introduced as per following engine 912 UL 4,407.160, 912 ULS 5,644.742, 914 UL 4,419.026;
b – With optimized spring routing;
c – see SI-912-020/914-022
Starting at: $0.12
B – Loctite 243
C – Loctite 648
L – Klueber Isoflex Topas Nb5051
O – Engine Oil
P – Loctite 5910
a – marked with S/N;
b – Only for model 2 and 4;
c – Tolerance group "C" 1.820 - 1.829 mm;
d – Tolerance group "D" 1.830 - 1.839 mm;
e – Depending on configuration use 14 studs P/N 840752 M8x201 or 8 studs M8x201 and 6 studs P/N 840754 m8x210;
f – See Overhaul Manual of the respective engine type, current issue;
g – Only for use with new cylinders 913221 with countersunk. With the cylinder 913225 the countersunk was already introduced starting from beginning of the production;
h – See the following Service Instruction current issue SI-914-021.
Starting at: $0.12
B – Loctite 243
L – Klueber Isoflex Topas Nb5051AR – As required
a – For cylinder 2 and 4;
b – From engine 912 UL S/N 4,401.595 up to 4,402.978, 914 UL S/N 4,417.708 up to 4,417.727;
c – From engine 912 UL S/N 4,402.979, 914 UL S/N 4,417.728;
d – Up to engine 912 UL S/N (Only if the engine was not refitted with intake manifolds 867683 and 867688) 4,402.978, 914 UL S/N 4,417.727;
e – Only at intake manifold without O-ring;
f – See following Service Bulletin SB-912-030 / current issue SB-914-019;
g – Not suitable for direct installation of the air filter on the carburetor. Forseen for airboxes without drip tray;
h – For rework of exhaust port. See Maintenance Manual Heavy of the respective engine type, current issue;
i – In a roll;
j – See Service Instruction SI-914-020 / current issue SI-914-022;
k – For cylinder 1 and 3;
l – Intake manifold with connection boss for pneumatic carburetor-synchronization. From engine 912 UL S/N 4,404.045, 912 ULS 4,426.475, 914 UL 4,417.956
Starting at: $0.12
B – Loctite 243
C – Loctite 648
L – Klueber Isoflex Topas Nb5051
O – Engine Oil
P – Loctite 5910
a – marked with S/N;
b – Only for model 2 and 4;
c – Tolerance group "C" 1.820 - 1.829 mm;
d – Tolerance group "D" 1.830 - 1.839 mm;
e – Depending on configuration use 14 studs P/N 840752 M8x201 or 8 studs M8x201 and 6 studs P/N 840754 m8x210;
f – See Overhaul Manual of the respective engine type, current issue;
g – Only for use with new cylinders 913221 with countersunk. With the cylinder 913225 the countersunk was already introduced starting from beginnng of the production;
h – See the following Service Instruction current issue SI-914-021;
i – Without O-Ring from S/N 06.0010 to 07.5000, 2x O-Ring starting with S/N 07.5001;
j – 431570 introduced as per engine S/N as follows: 912 UL S/N 06,770.893, 912 ULS S/N 06,781.191, 914 UL S/N 07,682.596;
k – Wrench size A/F 11