Search results for 'SPARK PLUGS AND ACCESSORIES'

A – Loctite 221
B – Loctite 243
C – Loctite 648
D – Loctite 574
O – Engine Oil

a – 582 UL DCDI mod. 99 rotary valve for configuration with rotary seal;
b – 582 UL DCDI mod. 99 the circlip must be positioned at the inner groove only;
e – Crankcase including rotary valve drive, configuration with rotary seal model 99

B – Loctite 243

a – For cylinder 1/3;
b – For cylinder 2/4;
c – Carburetor housing not available as spare part. Use carburetor assembly; 
d – Refer to service instruction SI-03-1998 current issue;
e – With clearance for O-ring (use only together with O-ring pos. 16 P/N 950430);
f – See SI-912-012, SI-914-014 current issue;
g – For airbox P/N 667167, See SI-914-015 current issue, For engine S/N 914 UL 4,418.634;
h – For airbox P/N 867753 or 667162, See SI-914-013 and SI-914-002 current issue;
i – Package including two floats;
j – At carburetor 1/3 only 1 piece;
k – Contain parts requirement for 2 carburetors

A – Loctite 221
B – Loctite 243
C - Loctite 648

c – Tighten to leave 1mm distance between starter cover and electric starter

B – Loctite 243
I – Lithium-Base Grease
O – Engine Oil

a – Stator retrofit kits: 912 UL: S/N 3,792.501 up to 3,792.55 Set D P/N 888716, S/N 4,005.300 up to 4,152.111 Set E P/N 888718, S/N 3,792.556 up to 4,005.299, Set C P/N 888714; S/N 4,152.112 up to 4,403.282 Set B P/N 888712; 912 ULS: S/N 4,425.001 up to 4,425.029 Set A P/N 888710; 914 UL: S/N 4,417.503 up to 4,417.783 Set B S/N 888712;
b – With modified trigger, instead of 4° before top dead center --> -3° after top dead center;
c – SI-912-013 / SI-914-016 standardization of the ignition unit;
d – Trigger coil kit with elongated hole for adjustment and 6-pole connector incl. 7 Stk. P/N 827800;
e – 4-pole connector and trigger coils without alignment incl. 7 Stk. P/N 827800. Replaced trigger coil kit P/N 965177;
f – Trigger coils for rev. counter to P/N 965176 and P/N 965179;
g – At all trigger coils with longhole

a – Crankcase with screw connection M8x18, b – Marked with groove, c - See Overhaul Manual of the respective engine type, current issue.

C – Loctite 638
L – Klueber Isoflex Topas Nb5051
O – Engine Oil

AR – As required

a – For cylinder 2 and 3;
b – For cylinder 1 and 4;
c – Up to engine S/N 912 UL: 4,401.879, 914 UL: 4,417.597, single valve springs and double valve springs if required are allowed to be mounted in one engine;  
d – From engine S/N 912 UL: 4,401.880, 914 UL: 4,417.598;
e – With sintered bronze bushing;
f – Oversize +0.2 mm (0.008 in.);
g – Rocker arm version with vespel bushing, from engine S/N 912 UL: 4,404.621, 912 ULS: 4,427.487, 914 UL: 4,418.104;
h – For inlet valve, chafe up to new measurement;
i –  For outlet valve, chafe up to new measurement;
j – Use only once!;
k – For rework of exhaust port. See Overhaul Manual of the respective engine type, current issue;
l – Marked with S/N;
m – Without worm gear;
n – Prefilled, 8 parts per set;
o – Cylinder heads where the coolant temperature is measured.
p – see SI-914-30

A – Loctite 221
C – Loctite 648
E – Loctite Anti-Seize
H – Loctite 603
I – Lithium-Base Grease
Q – 732 RTV

AR – As required

a – Replace layshift gear 55 T and pinion shaft 21 T only together;
b – Replace layshift gear 57 T and pinion shaft 19 T only together;
c – Replace layshift gear 59 T and pinion shaft 17 T only together;
d – Replace layshift gear 60 T and pinion shaft 15 T only together;
e – Attention: Left handed thread;
f – Coupling-flange Part No. 958 971 and sealing ring Part No. 950 084 has to be used as a set;
h – Gear set and splitted cone sleeve must be used together;
|| – NOTE: Included starter relay;
See also SI-2ST-007

AR – As required

a – For specific use see installation sheet;
b – Use at intake silencer version;
c – For 582 UL mod. 90 without fresh oil injection;
d – With fresh oil injection

B – Loctite 243
I - Lithium-Base Grease
AG – Silicon Heat Compound

a – Sold by the meter (39");
e – Not necessary at intake manifold P/N 867688;
f – Introduced as S/N 04.0388 with altered insulation only for spare parts;
g – Not suitable for crankcase P/N 886354, P/N 886358 and older;
h – At crankcase P/N 888364 or newer crankcase;
i – Not suitable for intake manifold P/N 867688;
j – Necessary at version with ring mount;
k – Sold by the meter (39");
l – Use P/N 842742 and 953390 only together;
m – SI-912-013 / SI-914-016 current issue. See Maintenance Manual Heavy of the respective engine type, current issue. From engine 912 UL S/N 4,406.291, 912 ULS S/N 5,643.680, 914 UL 4,418.712;
n - In a roll, silicone hose 120 mm;
o – SI-912-020 / SI-914-022 current issue;
p – 1x lock washer A6 P/N 945751 is not needed after production-year 2010 on position between the bracket 2 P/N 851267 and the hex nut M6

B – Loctite 243
E – Anti-Seize
I – Lithium-Base Grease
O – Engine Oil

a – From engine S/N 582 UL Mod. 90 5,236.549 piston for monohook circlip configuration (see also SI-2ST-001);
b – With 2 rings, standard;
c – With 2 rings, 1st oversize;
d – with 2 rings, 2nd oversize;
e – Standard size;
f – 1st oversize;
g – 2nd oversize; 
h – For use with piston Part No. 888 590 (Also see SI-2ST-001);
i – Use only once

A – Loctite 221
B – Loctite 243
C - Loctite 648

a – From engine S/N 582 UL Mod. 90: 4,015.239. and beginning of serial production 582 UL Mod 99;
c – Tighten to leave 1 mm distance between starter cover and electric starter;
d – 582 UL Mod. 90 until engine S/N 4.015.238 (without hydro damper assembly)

B – Loctite 243
C – Loctite 648
L – Klueber Isoflex Topas Nb5051
P – Loctite 5910

A – For version 2 with narrow dog gear (22 mm / 0.87 in.)
B – For version 3 with narrow dog gear (22 mm / 0.87 in.)
C – For version 4 with narrow dog gear (22 mm / 0.87 in.)
D – For version 2 with wide dog gear (27 mm / 1.06 in.); For 914 use only from following engine S/N 914 UL: 4,417.791
E – For version 3 with wide dog gear (27 mm / 1.06 in.); For 914 use only from following engine S/N 914 UL: 4,417.791
F – For version 4 with wide dog gear (27 mm / 1.06 in.); For 914 use only from following engine S/N 914 UL: 4,417.791
G – Replacement for 887701 with wide dog gear
H – Replacement for 887706 with wide dog gear
I – Replacement for 887711 with wide dog gear
J – Replacement for 887680 with wide dog gear
K – Replacement for 888565 with wide dog gear

a – Drive gear 22 T. and reduction gear 50 T. are paired and must be replaced together and marked with S/N. See SL-912-002 resp. SL-914-002.
b – Drive gear 21 T and reduction gear 51 T. are paired and must be replaced together and marked with S/N. With wide dog (27 mm / 1.06 in.); See SL-912-002 respr. SL-914-002; For 914 use only from following engine S/N: 912 ULS starting with serial production, 914 UL: 4,417.791
c – For model 2 marked with S/N
d – For model 3 marked with S/N
e – For model 4 marked with S/N
f – For gear sets P/N 886125 and 886517 (narrow versions)
g– For gear set P/N 886518 (wide version)
h – Drive gear 21 T. and reduction gear 51 T. are paired and must be replaced together and marked with S/N. With thin dog gear (22 mm / 0.87 in.); See SL-912-002 resp. SL-914-002; For 914 use only up to S/N 914 UL: 4,417.790
i – Do not use at version with auxiliary alternator; only available as a set (includes 6 pieces)
j – Only when a governor is used
k – Version without governor: 2x940.591; with governor: see chapter 61.20.00
l – Dog hub with extended hub
m – With additional bores to drain lead
n – Increased support bearing diameter
o – See SL-912-002 current issue

A – Loctite 221
B – Loctite 243
C – Loctite 648
D – Loctite 574
J – Molykote 44 Medium

c – Up to engine S/N 582 UL Mod. 90 4,172.691 (see also SI-08-1994);
d – From engine S/N 582 UL Mod. 90 4,172.692 (see also SI-08-1994)

B – Loctite 243

a – For cylinder 2 and 1/3;
b – For cylinder 1 and 2/4;
c – Carburetor housing not available as spare part. Use carburetor assembly,
d – Refer to service instruction SI-03-1998 current issue,
e – With clearance for O-ring (use only together with O-ring pos. 18 (P/N 950430);
f – For airbox P/N 867758, P/N 867756; See SB-912-044;
g – See SI-912-012, SI-914-014;
h – Package including two floats;
i – Special jetting according to instructions of the manufacturer;
j – Contain parts requirement for 2 carburetors;
k – Overhaul kit for 1 carburetor

B – Loctite 243
C - Loctite 648
L – Klueber Isoflex Topas Nb5051
O – Engine Oil

a - Thread 3/4-16 UNF for oil filter 3 mm extended, Introduced as per following engine 912 UL 4,407.160, 912 ULS 5,644.742, 914 UL 4,419.026;
b – With optimized spring routing;
c – see SI-912-020/914-022

B – Loctite 243
C – Loctite 648
L – Klueber Isoflex Topas Nb5051
O – Engine Oil

AR – As required

F – Loctite 7063
L – Klueber Isoflex Topas Nb5051
O – Engine Oil
Z – Loctite 603

e – At 912 ULS the complete  piston with rings has to be exchanged up to S/N 4,425.123;
f – With countersunk for O-ring 830415. 912 UL: 4,403.679, 912 ULS: Starting with serial production, 914 UL: 4,417.868;
g – Note following Service Letter: SL-912-002 current issue, SL-914-002 current issue,
h – With expanded space of sprag clutch. Introduced as per following engine S/N 912 UL: 4,409.089, 912 ULS: 5,650.835, 914 UL: 6,772.727;
i - Balanced pistons set: max. difference 3 g

A – Loctite 221
C – Loctite 648
E – Loctite Anti-Seize
I – Lithium-Base Grease

AR – As required

a – Replace layshift gear 55 T and pinion shaft 21 T only together;
b – Replace layshift gear 57 T and pinion shaft 19 T only together;
c – Replace layshift gear 59 T and pinion shaft 17 T only together;
d – Replace layshift gear 60 T and pinion shaft 15 T only together;
e – Attention: Left handed thread;
f – Coupling-flange Part No. 958 971 and oil-seal Part No. 950 084 has to be used together;
h – Gear set and splitted cone sleeve 847 757 must be used together. Also see SI-2ST-007

a – Marked with S/N