Search results for 'SPARK PLUGS AND ACCESSORIES'

a – Marked with S/N

B – Loctite 243
I – Lithium-Base Grease

a – In a roll/Sold by the meter (39")

A – Loctite 221
B – Loctite 243
C – Loctite 648
D – Loctite 574
O – Engine Oil

a – 582 UL DCDI mod. 99 rotary valve for configuration with rotary seal;
b – 582 UL DCDI mod. 99 the circlip must be positioned at the inner groove only;
e – Crankcase including rotary valve drive, configuration with rotary seal model 99

B – Loctite 243
I – Lithium-Base Grease

a – In a roll/Sold by the meter (39")

B – Loctite 243
C – Loctite 648
L – Klueber Isoflex Topas Nb5051
O – Engine Oil

A – Loctite 221
B – Loctite 243
C – Loctite 648
D – Loctite 574
J – Molykote 44 Medium

c – Up to engine S/N 582 UL Mod. 90 4,172.691 (see also SI-08-1994);
d – From engine S/N 582 UL Mod. 90 4,172.692 (see also SI-08-1994)

a – RED 67.50 MM - 67.51 MM, GREEN 67.51 - 67.52 MM;
b – Cylinder PTO side;
c – Cylinder MAG side

A – Loctite 221
C – Loctite 648
E – Loctite Anti-Seize
I – Lithium-Base Grease

AR – As required

a – Exchange drive gear 19 T and dog gear 49 T only together;
b – Exchange drive gear 21 T and dog gear 47 T only together;
c – Exchange drive gear 20 T and dog gear 40 T only together.

A – Loctite 221
B – Loctite 243
C - Loctite 648

a – From engine S/N 582 UL Mod. 90: 4,015.239. and beginning of serial production 582 UL Mod 99;
c – Tighten to leave 1 mm distance between starter cover and electric starter;
d – 582 UL Mod. 90 until engine S/N 4.015.238 (without hydro damper assembly)

AR – As required

a – Brush not available as spare part, use brush holder assembly 866891

a – Useable for engine type 447 UL, 503 UL, 582 UL 90/99 and 618 UL;
b – For adjustment and control of the ignition timing;
c - To cover the crankcase;
d – To hold the oil pump gear;
e – To hold the magneto flywheel;
f – For magneto fly wheel;
g – For ball bearing 6206, crankshaft magneto side;
h – For ball bearing 6207, crankshaft;
i – For ring halves;
j – For puller;
k – For crankshaft PTO side;
l – For crankshaft magneto side;
m – For ball bearing

Q – 732 RTV

AR – As required

a – Use at 582 UL mod. 90;
b – Use at 582 UL mod. 99;
c – Not available as spare part, use 881460

A – Loctite 221
C – Loctite 648
E – Loctite Anti-Seize
H – Loctite 603
I – Lithium-Base Grease
Q – 732 RTV

AR – As required

a – Replace layshift gear 55 T and pinion shaft 21 T only together;
b – Replace layshift gear 57 T and pinion shaft 19 T only together;
c – Replace layshift gear 59 T and pinion shaft 17 T only together;
d – Replace layshift gear 60 T and pinion shaft 15 T only together;
e – Attention: Left handed thread;
f – Coupling-flange Part No. 958 971 and sealing ring Part No. 950 084 has to be used as a set;
h – Gear set and splitted cone sleeve must be used together;
|| – NOTE: Included starter relay;
See also SI-2ST-007

B – Loctite 243

a – For cylinder 2 and 1/3;
b – For cylinder 1 and 2/4;
c – Carburetor housing not available as spare part. Use carburetor assembly,
d – Refer to service instruction SI-03-1998 current issue,
e – With clearance for O-ring (use only together with O-ring pos. 18 (P/N 950430);
f – For airbox P/N 867758, P/N 867756; See SB-912-044;
g – See SI-912-012, SI-914-014;
h – Package including two floats;
i – Special jetting according to instructions of the manufacturer;
j – Contain parts requirement for 2 carburetors;
k – Overhaul kit for 1 carburetor