Search results for 'Ignition Coils'

A – Loctite 221
I – Lithium-Base Grease

a – For ignition circuit 1;
b – For ignition circuit 2;
c – From engine S/N 4,795.397;
d – Sold by the meter (39");
e – Magneto flywheel new version (with closed cage), torx screw also valid for old version. At disassembly and reassembly of the screw, the thread has to be cleaned of the remaining coating and secured with Loctite 221. As an alternative a new screw can be used.

a – Useable for engine type 447 UL, 503 UL, 582 UL 90/99 and 618 UL;
b – For adjustment and control of the ignition timing;
c - To cover the crankcase;
d – To hold the oil pump gear;
e – To hold the magneto flywheel;
f – For magneto fly wheel;
g – For ball bearing 6206, crankshaft magneto side;
h – For ball bearing 6207, crankshaft;
i – For ring halves;
j – For puller;
k – For crankshaft PTO side;
l – For crankshaft magneto side;
m – For ball bearing

A – Loctite 221
C – Loctite 648
I – Lithium-Base Grease

a – From engine S/N 582 UL DCDI mod. 90: 4,015.239, 582 UL DCDI mod. 99: at serial production;
b – For ignition circuit 1;
c – For ignition circuit 2;
d – Up to engine S/N 582 UL DCDI mod. 90: 4,015.238;
e – From engine S/N 582 UL DCDI mod. 90: 4,015.239, 582 UL DCDI mod. 99: at serial production;
f – Sold by the meter (39");
g – Without rewind starter

a – For installation of cylinder on the piston 67.5 mm;
b – For installation of cylinder on the piston 72 mm;
c – To hold the fan;
d – For aligning of cylinders at the intake flange;
e – For crankshaft bearing PTO side;
f – For positioning of crankshaft bearing PTO side;
g – For centering of the stator plate;
h – For piston pin 18 mm;
i – For installation of piston pin circlip 18 mm;
j – For the engine;
k – Without ignition and externals

B – Loctite 243
I – Lithium-Base Grease
O – Engine Oil

a – Stator retrofit kits: 912 UL: S/N 3,792.501 up to 3,792.55 Set D P/N 888716, S/N 4,005.300 up to 4,152.111 Set E P/N 888718, S/N 3,792.556 up to 4,005.299, Set C P/N 888714; S/N 4,152.112 up to 4,403.282 Set B P/N 888712; 912 ULS: S/N 4,425.001 up to 4,425.029 Set A P/N 888710; 914 UL: S/N 4,417.503 up to 4,417.783 Set B S/N 888712;
b – With modified trigger, instead of 4° before top dead center --> -3° after top dead center;
c – SI-912-013 / SI-914-016 standardization of the ignition unit;
d – Trigger coil kit with elongated hole for adjustment and 6-pole connector incl. 7 Stk. P/N 827800;
e – 4-pole connector and trigger coils without alignment incl. 7 Stk. P/N 827800. Replaced trigger coil kit P/N 965177;
f – Trigger coils for rev. counter to P/N 965176 and P/N 965179;
g – At all trigger coils with longhole